Hyundai Sonata LF: Fuel Delivery System / Delivery Pipe Repair procedures
|
In case of removing the high pressure fuel pump, high
pressure fuel pipe, delivery pipe, and injector, there may be injury
caused by leakage of the high pressure fuel. So don’t do any repair
work right after engine stops.
|
| 1. |
Turn the ignition switch OFF and disconnect the battery negative (-) cable. |
| 2. |
Release the residual pressure in fuel line.
(Refer to Fuel Delivery System - “Release Residual Pressure in Fuel Line”)
|
When removing the fuel pump relay, a Diagnostic Trouble Code
(DTC) may occur. Delete the code with the GDS after completion of
“Release Residual Pressure in Fuel Line” work. |
|
| 3. |
Remove the intake manifold.
(Refer to Engine Mechanical System - "Intake Manifold") |
| 4. |
Disconnect the injector connectors (A) and the rail pressure sensor connector (B). |
| 5. |
Remove the high pressure fuel pipe (C). |
| 6. |
Remove the engine oil gauge. |
| 7. |
Remove the installation bolt (D), and then remove the delivery pipe and injector assembly from the engine. 
|
| • |
Do not use already used injector fixing clip again. |
|
|
Do not reuse the support disc.
Do not reuse the injector rubber washer.
Do not reuse the combustion seal. |
| • |
Install the component with the specified torques. |
| • |
Note that internal damage may occur when the component is dropped. In this case, use it after inspecting. |
|
| • |
Apply engine oil to the injector O-ring. |
| • |
Do not use already used injector O-ring again. |
|
| • |
Do not use already used bolt again. |
|
| • |
When insert the injector, be careful not to damage the injector tip.
|
|
| 1. |
Install in the reverse order of removal.
Delivery pipe mounting bolt:
18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)
High pressure fuel pipe mounting nut:
26.5 ~ 32.4 N.m (2.7 ~ 3.3 kgf.m, 19.5 ~ 23.9 lb-ft)
|
|
Removal
1.
Turn the ignition switch OFF and disconnect the negative (-) battery cable.
2.
Disconnect the accelerator position sensor connector (A)...
Removal
Whenever the high pressure fuel pump, fuel pipe,
deliverypipe, or injector is removed immediately after shutting offthe
engine, an injury may be caused by the release ofhighly pressurized
fuel...
Other information:
Schematic
[EPB Type]
[General Type]
Terminal Funtion
[EPB Type]
PIN NODesciptionCurrentmaxmin1Voltage supply for pump motor39A 10A 2RR EPB motor power30A - 3RR EPB motor ground30A - 4- - - 5Local CAN High 30mA 20mA 6Electric parking brake signal 1 20mA - 7Electric parking brake signal 220mA - 8Electric parking brake signal 320mA - 9Electric parking brake signal 420mA - 10- - - 11- - - 12RL EPB motor ground30A - 13RL EPB motor power30A - 14Ground for solenoid valves and ECU30A 10A 15- - - 16ESS200mA 100mA 17FR Wheel speed sensor signal16...
Removal and Installation
1.
Remove the drive belt.
(Refer to Timing System - "Dreve Belt")
2.
Remove the engineroom under cover.
3.
Remove the passenger side front tire.
4.
Remove the crankshaft damper pulley (A).
Tightening torque :
(47...
Accelerator Pedal Repair procedures
High Pressure Fuel Pump Repair procedures