Hyundai Sonata LF: Rear Suspension System / Rear Lower Arm Repair procedures
| 1. |
Raise the vehicle, and make sure it is securely supported. |
| 2. |
Remove the wheel cap (A). 
|
Be careful not to damage to the wheel cap (A) when removing the it.
|
|
| 3. |
Remove the front wheel and tire (A) from front hub.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
|
|
Be careful not to damage to the hub bolts when removing the front wheel and tire (A). |
|
| 4. |
Remove the rear lower arm protector. 
|
| 5. |
Loosen the lower arm (A) mounting bolt and nut. And then remove the lower arm form the rear carrier.
Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)
|
| • |
Set up the transmission jack under the lower arm in order to remove the shock absorber in no-load condition . |
| • |
Record the position of the alignment marks before removing
the rear lower arm to keep from tightening the bolt and washer to the
wrong position or the wrong direction. |
|
|
| 6. |
Loosen the mounting bolt and nut. And then separate the shock absorber from the lower arm.
Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)
|
| • |
Set up the transmission jack under the lower arm in order to remove the shock absorber in no-load condition . |
| • |
Record the position of the alignment marks before removing
the rear lower arm to keep from tightening the bolt and washer to the
wrong position or the wrong direction. |
|
|
| 7. |
Loosen the bolt & nut and then remove the rear lower arm (A) from the sub frame.
Tightening torque :
107.9 ~ 117.7 N.m (11.0 ~ 12.0 Kgf.m, 79.6 ~ 86.8 lb-ft)
|
| • |
Set up the transmission jack under the lower arm in order to remove the shock absorber in no-load condition . |
| • |
Record the position of the alignment marks before removing
the rear lower arm to keep from tightening the bolt and washer to the
wrong position or the wrong direction.
|
|
|
| 8. |
Loosen the bolt & nut and then remove the rear lower arm (A) from the sub frame.
Tightening torque :
107.9 ~ 117.7 N.m (11.0 ~ 12.0 Kgf.m, 79.6 ~ 86.8 lb-ft)
|
|
| 1. |
Installation is the reverse of removal.
| • |
Install the component with the specified torques. |
| • |
When installing the bolt, install the lower arm in no-load condition by using the transmission jack. |
|
|
| 2. |
Check the alignment.
(Refer to Tires/Wheels - "Alignment")
|
| 1. |
Check the bushing for wear and deterioration. |
| 2. |
Check the rear lower arm for deformation. |
| 3. |
Check for all bolts and nut. |
| 4. |
Check the cracks or the cutting of the lower . |
Replacement
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the wheel cap (A).
Be careful not to damage to the wheel cap (A) when removing the it...
Replacement
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the wheel cap (A).
Be careful not to damage to the wheel cap (A) when removing the it...
Other information:
Description
The sensor contains a thermistor which measures the
temperature of the inside. The signal decided by the resistance value
which changes in accordance with perceived inside temperature, is
delivered to heater control unit and according to this signal the
control unit regulates incar temperature to intended value...
Components
1. Rear door inside handle cap2. Rear door pull cap3. Rear door trim4. Rear door module5. Rear door belt inside weatherstrip6. Rear door panel7. Rear door belt outside weatherstrip8. Rear door frame garnish9. Rear door delta inner cover 10...
Rear Upper Arm Repair procedures
Rear Assist Arm Repair procedures