Hyundai Sonata LF: Cylinder Block / Rear Oil Seal Repair procedures

Hyundai Sonata LF 2014-2019 Service Manual / Engine Mechanical System / Cylinder Block / Rear Oil Seal Repair procedures

Removal
1.
Remove the transaxle assembly.
(Refer to transaxle - "Manual Transaxle assembly, Auto Transaxle assembly")
2.
MT : Remove the flywheel.
(Refet to Cylinder Block - "Flywheel")
3.
AT : Remove the drive plate.
(Refet to Cylinder Block - "Drive Plate")
4.
Remove the rear oil seal (A).

Installation
1.
Install the rear oil seal.
(1)
Apply engine oil to a new oil seal lip.
(2)
Using the SST (09231-H1100, 09231-2B200) and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.

2.
MT : Install the flywheel.
(Refet to Cylinder Block - "FlyWheel")
3.
AT : Install the drive plate.
(Refet to Cylinder Block - "Drive Plate")
4.
Install the transaxle assembly.
(Refer to transaxle - "Manual Transaxle assembly, Auto Transaxle assembly")

    Rear Oil Seal Components and Components Location

    C..

    Cylinder Block Components and Components Location

    Components 1.  Cylinder block2.  Ladder frame3.  Crank shaft4.  Crank shaft upper bearing5.  Crank shaft lower bearing6.  Thrust bearing7...

    Other information:

    Hyundai Sonata LF 2014-2019 Service Manual: Front Seat Back Cover Components and Components Location


    C..

    Hyundai Sonata LF 2014-2019 Service Manual: Troubleshooting


    Trouble Symptom Charts Trouble Symptom 1 Trouble Symptom 2 Trouble symptomProbable causeRemedyThe set vehicle speed varies greatly upward or downward"Surging" (repeated alternating acceleration and deceleration) occurs after settingMalfunction of the vehicle speed sensor circuitRepair the vehicle speed sensor system, or replace the partMalfunction of ECMCheck input and output signals at ECM Trouble Symptom 3 Trouble symptomProbable causeRemedyThe CC system is not canceled when the brake pedal is depressedDamaged or disconnected wiring of the brake pedal switchRepair the harness or replace the brake pedal switchMalfunction of the ECM signalsCheck input and output signals at ECM Trouble Symptom 4 Trouble symptomProbable causeRemedyThe CC system is not canceled when the shift lever is moved to the "N" position (It is canceled, however, when the brake pedal is depressed)Damaged or disconnected wiring of inhibitor switch input circuitRepair the harness or repair or replace the inhibitor switchImproper adjustment of inhibitor switchMalfunction of the ECM signalsCheck input and output signals at ECM Trouble Symptom 5 Trouble symptomProbable causeRemedyCannot decelerate (coast) by using the "SET/–" switchTemporary damaged or disconnected wiring of "SET/–" switch input circuitRepair the harness or replace the "SET/–" switchMalfunction of the ECM signalsCheck input and output signals at ECM Trouble Symptom 6 Trouble symptomProbable causeRemedyCannot accelerate or resume speed by using the "RES/+" switchDamaged or disconnected wiring, or short circuit, or "RES/+" switch input circuitRepair the harness or replace the "RES/+" switchMalfunction of the ECM signalsCheck input and output signals at ECM Trouble Symptom 7 Trouble symptomProbable causeRemedyCC system can be set while driving at a vehicle speed of less than 40km/h (25mph), or there is no automatic cancellation at that speedMalfunction of the vehicle-speed sensor circuitRepair the vehicle speed sensor system, or replace the partMalfunction of the ECM signalsCheck input and output signals at ECM Trouble Symptom 8 Trouble symptomProbable causeRemedyThe cruise main switch indicator lamp does not illuminate (But CC system is normal)Damaged or disconnected bulb of cruise main switch indicator lampRepair the harness or replace the part...

    Categories

    read more

     
    Copyright © 2026 www.hsonatalf.org