Hyundai Sonata LF: Airbag Module / Airbag Module Disposal Description and Operation

Hyundai Sonata LF 2014-2019 Service Manual / Restraint / Airbag Module / Airbag Module Disposal Description and Operation

Airbag Disposal
Special tool required
Deployment tool 0957A-34100A
Before scrapping any airbags or side airbags (including those installed in vehicle to be scrapped), the airbags or side airbags must be deployed. If the vehicle is still within the warranty period, before deploying the airbags or side airbags, the Technical Manager must give approval and/or special instruction. Only after the airbags or side airbags have been deployed (as the result of vehicle collision, for example), can they be scrapped. If the airbags or side airbags appear intact (not deployed), treat them with extreme caution. Follow these procedures:
Deploying Airbags in the Vehicle
If an SRS equipped vehicle is to be entirely scrapped, the airbags or side airbags should be deployed while still in the vehicle. The airbags or side airbags should not be considered as salvageable parts and should never be installed in another vehicle.
1.
Turn the ignition switch OFF, and disconnect the battery negative cable and wait at least three minutes.
2.
Confirm that each airbag or side airbag is securely mounted.
3.
Confirm that the special tool is functioning properly by following the check procedure.
(1)
Driver’s Airbag :
A.
Remove the driver’s airbag and install the SST (0957A-3Q100).
B.
Install the driver’s airbag on the steering wheel.
(2)
Front Passenger’s Airbag :
A.
Remove the glove box housing, and then disconnect the connector between the front passenger’s airbag and SRS main harness.
B.
Install the SST (0957A-3Q100).
(3)
Side Airbag :
A.
Disconnect the 2P connector between the side airbag and wire harness.
B.
Install the SST (0957A-3F100).
(4)
Curtain Airbag :
A.
Disconnect the 2P connector between the curtain airbag and wire harness.
B.
Install the SST (0957A-3Q100).
(5)
Seat Belt Pretensioner :
A.
Disconnect the 2P connector from the seat belt pretensioner.
B.
Install the SST (0957A-3Q100).
(6)
Emergency Fastening Device :
A.
Disconnect the 2P connector from the emergency fastening device.
B.
Install the SST (0957A-3Q100).
(7)
Knee Airbag :
A.
Disconnect the connector between the knee airbag and wire harness.
B.
Install the SST (0957A-3F100).
4.
Place the deployment tool at least thirty feet (10meters) away from the airbag.
5.
Connect a 12 volt battery to the tool.
6.
Push the tool’s deployment switch. The airbag should deploy (deployment is both highly audible and visible: a loud noise and rapid inflation of the bag, followed by slow deflation)
7.
Dispose of the complete airbag. No parts can be reused. Place it in a sturdy plastic bag and seal it securely.
Deploying the Airbag Out of the Vehicle
If an intact airbag has been removed from a scrapped vehicle, or has been found defective or damage during transit, storage or service, it should be deployed as follows:
1.
Confirm that the special tool is functioning properly by following the check procedure on this page.
2.
Position the airbag facing up, outdoors on flat ground at least thirty feet (10meters) from any obstacles or people.
Disposal of Damaged Airbag
1.
If installed in a vehicle, follow the removal procedure of driver’s airbag, front passenger’s and side airbag.
2.
In all cases, make a short circuit by twisting together the two airbag inflator wires.
3.
Package the airbag in exactly the same packing that the new replacement part came in.

    Knee Airbag (KAB) Module Repair procedures

    Removal 1. Disconnect the battery negative cable and wait for at least three minutes before beginning work. 2. Remove the crash pad lower panel...

    Seat Belt Pretensioner

    ..

    Other information:

    Hyundai Sonata LF 2014-2019 Service Manual: Rear Seat Folding Lever Repair procedures


    Replacement 1. Fold the rear seat back assembly (A) by pulling the folding lever in the direction of the arrow. 2. After loosening the mounting bolts, then remove the rear seat folding lever (A). 3. Install in the reverse order of removal...

    Hyundai Sonata LF 2014-2019 Service Manual: Schematic Diagrams


    Schematic [EPB Type] [General Type] Terminal Funtion [EPB Type] PIN NODesciptionCurrentmaxmin1Voltage supply for pump motor39A 10A 2RR EPB motor power30A - 3RR EPB motor ground30A - 4- - - 5Local CAN High 30mA 20mA 6Electric parking brake signal 1 20mA - 7Electric parking brake signal 220mA - 8Electric parking brake signal 320mA - 9Electric parking brake signal 420mA - 10- - - 11- - - 12RL EPB motor ground30A - 13RL EPB motor power30A - 14Ground for solenoid valves and ECU30A 10A 15- - - 16ESS200mA 100mA 17FR Wheel speed sensor signal16...

    Categories

    read more

     
    Copyright © 2025 www.hsonatalf.org