Hyundai Sonata LF: Body (Interior and Exterior) / Front Bumper
Components and Components Location
1. Front bumper cover
| 2. Front bumper side bracket
|
Front Bumper Cover Components and Components Location
Front Bumper Cover Repair procedures
| • |
Put on gloves to protect your hands. |
|
| • |
When prying with a flat-tip screwdriver or use a prying trim
tool, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage. |
| • |
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface. |
| • |
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Loosen the front bumper upper mounting clips. 
|
| 2. |
Loosen the front bumper lower mounting clips. 
|
| 3. |
After loosening the front bumper (A) side's mounting clips and screw, then disconnect the side's.
| • |
Remove the front bumper by pulling up the side of the front bumper and then pull it out. |
|
| • |
When you pull out the front bumper, the side part of the front bumper could be damaged by the projection. |
|
|
| 4. |
Disconnect the front bumper main connector (A). 
|
| 5. |
Remove the front bumper cover (A). 
|
| 6. |
Install in the reverse order of removal.
| • |
Make sure the connector is connected properly. |
| • |
Replace any damage clips. |
|
|
Radiator Grill Components and Components Location
Radiator Grill Repair procedures
| • |
Put on gloves to protect your hands. |
|
| • |
When prying with a flat-tip screwdriver or use a prying trim
tool, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage. |
| • |
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface. |
| • |
Take care not to bend or scratch the trim and panels. |
|
| 1. |
Remove the front bumper cover.
(Refer to Front Bumper - "Front Bumper Cover") |
| 2. |
Remove the mounting clip (A) and then remove the front bumper energy absorber (B). 
|
| 3. |
Remove the pantoscopic camera.
(Refer to Body Electrical System - "Pantoscopic Camera") |
| 4. |
Loosen the radiator grill mounting screws. |
| 5. |
Unlock the lock pins by pushing it up with a screwdriver or remover and then remove the radiator grill (A). 
|
| 6. |
Install in the reverse order of removal.
| • |
Replace any damage clips. |
|
|
Repair procedures
Replacement
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver or use a prying trim
tool, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage...
Components and Components Location
Components
1. Rear bumper cover2. Rear bumper retainer cover3. Rear bumper side bracket [LH]4. Rear bumper side bracket [RH]
Rear Bumper Cover Components and Components Location
Component Location
1...
Other information:
Removal and Installation
1.
Remove the engine cover.
2.
Disconnect the battery negative terminal.
3.
DIsconnect the air duct (A).
4.
Remove the air duct and air cleaner assembly.
Tightening torque
Hose clamp bolt:
2.9 ~ 4.9N.m (0...
Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Lower Panel")
3.
Disconnect the 6P connector (B) of the coil antenna and then remove the coil antenna (A) after loosening the screw...
Floor Carpet. Repair procedures
Rear Bumper