Hyundai Sonata LF: Body Dimensions / Interior Body Repair
| Interior A |
| * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] |
| Interior B |
| * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] |
| Interior C |
| * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] |
| Interior D |
| * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] |
| Interior E |
| * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] |
| Interior F |
| * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] |
|
|
|
| Front pillar upper extension tooling hole (O7) | Curtain airbag mounting hole (O6.6) | Curtain airbag mounting hole (O6.6) |
|
|
|
| Cowl crossbar mounting hole (O9) | Cowl side trim mounting hole (O8.4) | Front door checker mounting hole (O13) |
|
|
|
| Curtain airbag mounting hole (O6.6) | Seat belt height adjuster upper mounting hole (O16) | Seat belt pretensioner mounting hole (O14) |
|
|
|
| Rear door checker mounting hole (O13) | Curtain airbag mounting hole (O6.6) | Rear pillar trim mounting hole (O6.6) |
|
|
|
| Rear door striker mounting hole (O13) | Quarter inner lower panel tooling hole (O16) | Quarter inner panel tooling hole (O6.6) |
|
|
|
| Quarter inner panel tooling hole (O7) | Quarter inner panel tooling hole (O7) | Center floor panel tooling hole (O9) |
|
|
|
| Side sill inner reinforcement tooling hole (O7) | Front step tooling hole (O10) | Front seat mounting hole (O13) |
|
|
|
| Front seat mounting hole (O11) | Front seat mounting hole (O11) | Front seat mounting hole (O11) |
|
|
|
| Center side sill corner | Rear floor panel tooling hole (O15) | Rear seat mounting hole (O18) |
|
|
|
| Quarter inner panel tooling hole (O6.6) | Quarter inner lower panel tooling hole (O5.5) | Rear floor extension tooling hole (O8) |
|
|
|
| Rear floor extension tooling hole (O8) | Rear floor panel mounting hole (O14) | Rear floor panel mounting hole (O14) |
|
| |
| Rear floor panel mounting hole (O13) | Rear transverse trim mounting hole (O8.4) |
Side Body Body Repair
Side Body A * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] Side Body B * These dimensions indicated in this figure are actual-measurement dimensions...
Rear Body Body Repair
* These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] Side outer panel rear cornerSide outer panel rear cornerSide outer panel rear cornerRear combination lamp mounting hole (O6)Rear bumper mounting hole (8...
Other information:
Hyundai Sonata LF 2014-2019 Service Manual: Ambient Temperature Sensor Repair procedures
Inspection 1. Check the resistance of the ambient temperature sensor between terminals 1 and 2 whether it changes by changing the ambient temperature. 1. Ambient Sensor (+)2. Sensor ground Specification Ambient temperature[°C (°F)] Resistance between terminal 1 and 2 (k?)-40 (-40)881...
Hyundai Sonata LF 2014-2019 Service Manual: Rear Disc Brake Repair procedures
Removal [General Type] 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the wheel cap(A). Be careful not to damage to the wheel cap(A) when removing the it. 3. Remove the front wheel and tire (A) from front hub...
Categories
- Manuals Home
- Hyundai Sonata Owners Manual
- Hyundai Sonata Service Manual
- Brake System
- Alternator Repair procedures
- Cooling System
- New on site
- Most important about car
